CH Precision M-1.1 - Amplificateur de Puissance à 2 canaux (2 x 200W RMS 8Ω)

49'500.00 CHF La pièce
Summum de musicalité et de technologie, l'Amplificateur de Puissance CH PRECISION M 1.1 est un instrument de musique d'exception. Il est configurable et adaptable à l'infini. En mode MONO bridged il est capable de fournir 700 Watts en continu sous 8 Ohms! Tous les fabuleux instruments de musique CH PRECISION sont développés et fabriqués en +Suisse+.
Réserver une ecoute
Being able to truthfully and accurately reproduce today’s highest quality recordings has never been more challenging. Only when each element of the reproduction chain is able to precisely recreate the music’s time and level information can a genuine emotion be felt. The M1.1, CH Precision 1 Series’ most powerful amplifier was developed with this in mind. The leading-edge technological advancements implemented on the A1 were further refined, among others is the ExactBias circuitry and a finer loudspeaker matching.

Specified at 200W RMS into 8Ω in monaural mode, 2x 200W RMS into 8Ω in bi-amplification / Stereo modes and 700W RMS into 8Ω in bridge mode, the M1 houses a dedicated 2200VA power transformer providing the amplifier output stage with ample energy to accurately and effortlessly drive the most demanding loudspeakers.

Option board:
Analog_Buf: Monaural analog input buffer board à CHF 1'700.-
Three analog inputs - XLR, RCA and BNC - are provided on a single board. A pass-through XLR male connector allows a direct connection to another A1 amplifier.
Can be factory ordered for Left or Right channel.
Factory built-in (1x), second board is needed for stereo operation.

 
Analog inputs:
Inputs type Balanced (XLR), one connector per board
Single-Ended (RCA & BNC), one connector per board
Input impedance Balanced: 94kΩ
Single-Ended: 47kΩ or 300Ω
Input stage JFET input stage
Ultra-low noise, discrete fully differential stage
24dB range adjustable gain in 0.5dB steps

Amplification:
Amplification stage Ultra-low noise full discrete class AB design
6 pairs of complementary output transistors
Bias Patent-pending bias circuitry for constant bias operation
Feedback User-adjustable local vs. global feedback ratio, from 0% to 100% in 10% steps 
Bandwidth DC to 450kHz (-3dB) at 1W into an 8Ω resistive load
Signal to Noise Ratio Better than 115dB in stereo and bi-amp modes
Better than 118dB in bridge mode
Total Harmonic Distortion + Noise Less than 0.1% with 0% global feedback
Less than 0.01% with 100% global feedback

Analog outputs:
Binding posts Two pairs of Argento binding posts for loudspeakers connection
Monitoring Non-intrusive DSP-based protection of the amplifier and connected loudspeakers
Instantaneous voltage & current values are permanently monitored on each channel
Protections Short-circuit protected
Disconnected loudspeaker detected
Over-temperature of the heatsink
Over-temperature of the output transistors

Power supply:
Transformer 2'200VA toroidal transformer for output stages, oversized for low-noise operation
100VA separate toroidal transformer for input stages
Power capacitors  2x 100'000uF/100V 4-poles capacitors
Regulators Non-regulated symetrical power supply for the power stages
Eight local regulation stages for input/driver stages
Seven local regulation stages for the logic/display

General:
Display 480x272 pixels, 24bits color, AMOLED
Mains operation Selectable 100V, 115, 230V AC, 47-63Hz
Power supply consumption <1W (standby), 2200W max in operation
Dimensions/Weight 440 x 440 x 266mm (W x D x H), 75kg
Remote control Ethernet interface, TCP/IP control
Appelez 24/7 gratuitement
nos conseillers

0 800 800 660
Appelez 24/7 gratuitement
nos conseillers
0 800 800 660