Shunyata DELTA v2 S/PDIF - 1 meter
719.00 CHF pièce de 1 mètre758.00 Sie sparen 39.00
Shunyata DELTA V2 S/PDIF features a true balanced, twisted pair design. Ohnocontinuous cast copper, VTX™ (hollow core) conductors with expensive fluorocarbon dielectrics and braided shielding. Shunyata Research’s exclusiveKPIP™ process eliminates lengthy burn-in issues.
Beschreibung
PMZ
Shunyata Research digital cables are produced using a Precision Matched Impedance cable geometry. This means that tolerances of the conductor surface, dielectric extrusion, and the precision of the braided shield are held to minute variances. To achieve these tight tolerances, the extrusion and braiding machines must be run at one-quarter speed during the manufacturing process. The result is better performance through a reduction of cable-induced signal jitter.
ArNi®
Wire was created by Shunyata Research designed to be the finest quality wire available. It begins with the highest purity of copper available – OFE C101, SPC or Ohno (single crystal). Fluorocarbon dielectrics, usually only found in in the aerospace applications have special electrical characteristics including extremely low dielectric absorption, high dielectric strength and exceptional heat resistance. When used in digital wiring it significantly reduces transient energy storage and release which affects phase noise performance.
PMZ Connectors — Pulse timing is critical to digital transmission accuracy. It is critical that a digital connector’s impedance precisely match the cables's characteristic impedance. A mismatched connector will create signal reflections which increases digital jitter or phase noise. A 50-ohm cable requires a 50-ohm termination — not the commonly used 75-ohm connector. Shunyata Research is careful to ensure that every cable and connector are precisely matched for a seamless component to component connection.
Kinetic Phase Inversion Processing
Kinetic Phase Inversion Processing was developed by Caelin Gabriel after years of research into the underlying causes of various effects such as burn-in, wire directionality and the effects of cryogenic treatment. He discovered that there was an underlying core principle that burn-in and cryogenics only partially addressed. Once the governing principle was understood it became possible to create a processor that reduces the need for long burn-in periods and eliminates the effects of cryogenic treatment. Four-days of continuous KPIP™ processing dramatically reduces the sonic ups and downs associated with burn-in, delivering a relaxed and natural presentation.
APPLICATIONS
All music and sound systems, recording environments and studio systems.
It takes us fifteen days to get your cables to the length you need from Shunyata. Click on "Request Information" above to get an offer. It takes CHF 68.- by 0.25 meter extra and per pair to get the length you need.
Technische Daten Shunyata DELTAV2S/PDIF:
Cable Type: PMZ coaxial
Conductors: ArNi Silver
Dielectric: Fluorocarbon
Impedance: 75 ohms
Connectors: SR-RCAb-110
CMODE Modules: NA
KPIP Processing: 4-days
Length: 1 meter
Safety Assurance
Continuity and polarity tests – by two technicians
HiPOT tests insulation breakdown @ 1,200 VAC
Shunyata Research digital cables are produced using a Precision Matched Impedance cable geometry. This means that tolerances of the conductor surface, dielectric extrusion, and the precision of the braided shield are held to minute variances. To achieve these tight tolerances, the extrusion and braiding machines must be run at one-quarter speed during the manufacturing process. The result is better performance through a reduction of cable-induced signal jitter.
ArNi®
Wire was created by Shunyata Research designed to be the finest quality wire available. It begins with the highest purity of copper available – OFE C101, SPC or Ohno (single crystal). Fluorocarbon dielectrics, usually only found in in the aerospace applications have special electrical characteristics including extremely low dielectric absorption, high dielectric strength and exceptional heat resistance. When used in digital wiring it significantly reduces transient energy storage and release which affects phase noise performance.
PMZ Connectors — Pulse timing is critical to digital transmission accuracy. It is critical that a digital connector’s impedance precisely match the cables's characteristic impedance. A mismatched connector will create signal reflections which increases digital jitter or phase noise. A 50-ohm cable requires a 50-ohm termination — not the commonly used 75-ohm connector. Shunyata Research is careful to ensure that every cable and connector are precisely matched for a seamless component to component connection.
Kinetic Phase Inversion Processing
Kinetic Phase Inversion Processing was developed by Caelin Gabriel after years of research into the underlying causes of various effects such as burn-in, wire directionality and the effects of cryogenic treatment. He discovered that there was an underlying core principle that burn-in and cryogenics only partially addressed. Once the governing principle was understood it became possible to create a processor that reduces the need for long burn-in periods and eliminates the effects of cryogenic treatment. Four-days of continuous KPIP™ processing dramatically reduces the sonic ups and downs associated with burn-in, delivering a relaxed and natural presentation.
APPLICATIONS
All music and sound systems, recording environments and studio systems.
It takes us fifteen days to get your cables to the length you need from Shunyata. Click on "Request Information" above to get an offer. It takes CHF 68.- by 0.25 meter extra and per pair to get the length you need.
Technische Daten Shunyata DELTAV2S/PDIF:
Cable Type: PMZ coaxial
Conductors: ArNi Silver
Dielectric: Fluorocarbon
Impedance: 75 ohms
Connectors: SR-RCAb-110
CMODE Modules: NA
KPIP Processing: 4-days
Length: 1 meter
Safety Assurance
Continuity and polarity tests – by two technicians
HiPOT tests insulation breakdown @ 1,200 VAC
